 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| hardware documentation linear hall-effect sensor family with sent interface hal ? 283x hardware documentation ai000143-002en aug. 16, 2010 approval document edition sept. 6, 2010 ai000143-002en a d v a n c e i n f o r m a t i o n edition ??? 6251-???-?pd p re l i m i n a r y d a t a s h e e t edition ??? 6251-???-?ds d a t a s h e e t free datasheet http://www.datasheet-pdf.com/
hal 283x advance information 2 sept. 6, 2010; ai000143-002en micronas copyright, warranty, and limitation of liability the information and data contained in this document are believed to be accurate and reliable. the software and proprietary information contained therein may be protected by copyright, patent, trademark and/or other intellectual property rights of micronas. all rights not expressly granted remain reserved by micronas. micronas assumes no liability for errors and gives no warranty representation or guarantee regarding the suitability of its products for any particular purpose due to these specifications. by this publication, micronas does not assume respon- sibility for patent infringements or other rights of third parties which may result from its use. commercial con- ditions, product availability and delivery are exclusively subject to the respective order confirmation. any information and data which may be provided in the document can and do vary in different applications, and actual performance may vary over time. all operating parameters must be validated for each customer application by customers? technical experts. any new issue of this document invalidates previous issues. micronas reserves the right to review this doc- ument and to make changes to the document?s content at any time without obligation to notify any person or entity of such revision or changes. for further advice please contact us directly. do not use our products in life-supporting systems, aviation and aerospace applications! unless explicitly agreed to otherwise in writing between the parties, micronas? products are not designed, intended or authorized for use as components in systems intended for surgical implants into the body, or other applica- tions intended to support or sustain life, or for any other application in which the failure of the product could create a situation where personal injury or death could occur. no part of this publication may be reproduced, photo- copied, stored on a retrieval system or transmitted without the express written consent of micronas. micronas trademarks ?hal third-party trademarks all other brand and product names or company names may be trademarks of their respective companies. free datasheet http://www.datasheet-pdf.com/ contents page section title micronas sept. 6, 2010; ai000143-002en 3 advance information hal 283x 4 1. introduction 4 1.1. major applications 4 1.2. features 5 1.3. marking code 5 1.4. operating junction temperature range (t j ) 5 1.5. hall sensor package codes 5 1.6. solderability and welding 5 1.7. pin connections and short descriptions 6 2. functional description 6 2.1. general function 7 2.2. digital signal processing 8 2.2.1. temperature compensation 9 2.2.2. dsp configuration registers 12 2.3. power-on self test (post) 13 3. specifications 13 3.1. outline dimensions 17 3.2. dimensions of sensitive area 17 3.3. positions of sensitive area 17 3.4. absolute maximum ratings 17 3.4.1. storage, moisture sensitivity class, and shelf life 18 3.5. recommended operating conditions 18 3.6. electrical characteristics 19 3.7. magnetic characteristics 20 3.8. thermal characteristics 20 3.8.1. definition of sensitivity error es 22 4. the sent module 27 5. programming of the sensor 27 5.1. programming interface 28 5.2. programming environment and tools 28 5.3. programming information 29 6. application notes 29 6.1. ambient temperature 29 6.2. emc and esd 29 6.3. application circuit 32 7. data sheet history free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 4 sept. 6, 2010; ai000143-002en micronas linear hall-effect sensor family with sent inter- face release note: revision bars indicate significant changes to the previous edition. 1. introduction the hal 283x are members of the micronas family of programmable linear hall-effect sensors. the subfam- ily hal 283x consists of the four members described in the following table: the hal 283x features a temperature-compensated hall plate with spinning current offset compensation, an a/d converter, digital signal processing, an eeprom memory with redundancy and lock function for the calibration data, and protection devices at all pins. the internal digital signal processing is of great benefit because analog offsets, temperature shifts, and mechanical stress do not degrade digital signals. the easy programmability allows a 2-point calibration by adjusting the output signal directly to the input sig- nal (like mechanical angle, distance, or current). indi- vidual adjustment of each sensor during the cus- tomer?s manufacturing process is possible. with this calibration procedure, the tolerances of the sensor, the magnet, and the mechanical positioning can be com- pensated in the final assembly. in addition, the temperature compensation of the hall ic can be fit to all common magnetic materials by pro- gramming first- and second-order temperature coeffi- cients of the hall sensor sensitivity. it is also possible to compensate offset drifts over temperature gener- ated by the customer application with a first order tem- perature coefficient of the sensors offset. this enables operation over the full temperature range with high accuracy. for programming purpose, the sensor features a pro- gramming interface with a biphase-m protocol on the dio pin (output). in the application mode, the sensor provides a continu- ous sent data stream. 1.1. major applications ? contactless potentiometers ? angular measurements (e.g. valve, throttle, pedal position) ? linear movement (e.g. seat track position) ? linear force or torque measurements ? current sensing (e.g. battery management) 1.2. features ? high precision linear hall-effect sensor ? spinning current offset compensation ? 20 bit digital signal processing ? output resolution up to 16 bit ? esd protection ( 8 kv hbm) at all pins and reverse protection at v sup pin ? various sensor parameter are programmable (like offset, sensitivity, temperature coefficients, etc.) ? nv memory with redundancy and lock function ? programmable temperature compensation for sen- sitivity (2 nd order) and offset (1 st order) ? typical magnetic ranges from 20 mt up to 160 mt in 20 mt steps ? sample period programmable from 0.5 ms to 33 ms. second-order low-pass filter for sample period down to 2 ms ? onboard diagnostics (overvoltage, output current, overtemperature, signal path overflow) ? power-on self-test covering memory and full signal path from hall plates to sent output ? biphase-m interface (programming mode) ? sent clock tick time programmable between 2 s and 17.75 s ? low tick time programmable between 3 and 6.75 clock ticks ? sample accurate transmission of magnetic field information ? transmission of temperature and device information by serial data messages in the status nibble ? open-drain output with slew-rate control (load inde- pendent) ? programming and operation of multiple sensors at the same supply line table 1?1: family overview type resolution pause pulse sent version HAL2830 12 bit no sae-j2716 release 2010-01 hal 2831 16 bit no sae-j2716 release 2010-01 hal 2832 12 bit yes sae-j2716 release 2010-01 hal 2833 16 bit yes sae-j2716 release 2010-01 free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 5 1.3. marking code the hal 283x have a marking on the package surface (branded side). this marking includes the name of the sensor and the temperature range. 1.4. operating junction temperature range (t j ) the hall sensors from micronas are specified to the chip temperature (junction temperature range t j ). a: t j = ? 40 c to +170 c k: t j = ? 40 c to +140 c the relationship between ambient temperature (t a ) and junction temperature is explained in section 6.1. on page 29 1.5. hall sensor package codes hall sensors are available in a wide variety of packag- ing versions and quantities. for more detailed informa- tion, please refer to the brochure: ?hall sensors: ordering codes, packaging, handling?. 1.6. solderability and welding solderability during soldering reflow processing and manual reworking, a component body temperature of 260 c should not be exceeded. welding device terminals should be compatible with laser and resistance welding. please note that the success of the welding process is subject to different welding parameters which will vary according to the welding technique used. a very close control of the welding parameters is absolutely necessary in order to reach satisfying results. micronas, therefore, does not give any implied or express warranty as to the ability to weld the component. 1.7. pin connections and short descriptions fig. 1?1: pin configuration type temperature range a k HAL2830 2830a 2830k hal 2831 2831a 2831k hal 2832 2832a 2832k hal 2833 2833a 2833k halxxxxpa-t temperature range: a or k package: ut for to92ut -1/-2 type: 2832 example: hal2832ut-k type: 2832 package: to92ut-1/-2 temperature range: t j = ? 40 c to +140 c pin no. pin name type short description 1 vsup supply voltage 2 gnd ground 3dioin/ out digital io sent output 1 vsup 2gnd 3 dio free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 6 sept. 6, 2010; ai000143-002en micronas 2. functional description 2.1. general function the hal 283x is a monolithic integrated circuit, which provides an output signal proportional to the magnetic flux through the hall plate. the external magnetic field component, perpendicular to the branded side of the package, generates a hall voltage. the hall ic is sensitive to magnetic north and south polarity. this voltage is converted to a digital value, processed in the digital signal processing unit (dsp) according to the settings of the eeprom regis- ters. the function and the parameters for the dsp are explained in section 2.2. on page 7. internal temperature compensation circuitry and the spinning current offset compensation enables opera- tion over the full temperature range with minimal changes in accuracy and high offset stability. the cir- cuitry also rejects offset shifts due to mechanical stress from the package. the hal 283x provides two operation modes, the application mode and the programming mode. application mode the output signal is provided as continuous sent data stream. programming mode for the programming of the sensor parameters, a biphase-m protocol is used. the hal 283x provides non-volatile memory which is divided in different blocks. the first block is used for the configuration of the digital signal processing, the second one is used by the various customer settings. the non-volatile memory employs inherent redun- dancy. fig. 2?1: hal 283x block diagram internally temperature oscillator switched a/d digital dio vsup gnd eeprom memory lock control stabilized supply and protection devices dependent bias protection devices hall plate converter signal processing sent module temperature a/d sensor converter programming interface open-drain output with slew control free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 7 2.2. digital signal processing all parameters and the values y, y tci are normalized to the interval ( ? 1, 1) which represents the full-scale mag- netic range as programmed in the range register. example for 40 mt range ? 1 equals ? 40 mt +1 equals + 40 mt for the definition of the register values, please refer to section 2.2.2. on page 9. the digital signal processing (dsp) is the major part of the sensor and performs the signal conditioning. the parameters of the dsp are stored in the dsp config area of the eeprom. the device provides a digital temperature compensa- tion. it consists of the internal temperature compensa- tion, the customer temperature compensation, as well as an offset and sensitivity adjustment. the internal temperature compensation (factory compensation) eliminates the temperature drift of the hall sensor itself. the customer temperature compensation is cal- culated after the internal temperature drift has been compensated. thus, the customer has not to take care about the sensor?s internal temperature drift. the output value y is calculated out of the factory-com- pensated hall value y tci as: parameter d is representing the offset and c is the coefficient for sensitivity. the signal path contains a digital low-pass filter up to second order with a programmable sampling fre- quency from 32 hz up to 2 khz (see table 2?2 on page 11). fig. 2?2: block diagram of digital signal path including digital filter yy tci dtval () + [] c tval () ? = internal temp. a d t (temp.) comp. custom. temp. comp. offset & sens. adjustm. a d dec hardware b y tci tval hvd range conversion to 16 bit 20 16 d sent i/o logic y tick, lt sample rate 13 to 16 13 to 16 20 31 to 2000 hz depends on sent note: hval is stored in hvd register filter free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 8 sept. 6, 2010; ai000143-002en micronas the temperature-compensated hall value is saved in the hvd register. the sent interface transmits continuously hall sam- ples. the hvd value is transmitted at the the begin- ning of a new sent message. after power-up, the registers hvd and tvd are set to the negative overflow value until valid data are avail- able. 2.2.1. temperature compensation terminology: d0: name of the register or register value d 0 : name of the parameter the customer programmable parameters ?c? (sensitiv- ity) and d (offset) are polynomials of the temperature. the temperature is represented by the adjusted read- out value tval of a built-in temperature sensor. the update rate of the temperature value tval is less than 100 ms. the sensitivity polynomial c(tval) is of second order in temperature: for the definition of the polynomial coefficients, please refer to section 2.2.2. on page 9. the offset polynomial d(tval) is linear in temperature: for the definition of the polynomial coefficients, please refer to section 2.2.2. on page 9. for the calibration procedure of the sensor in the sys- tem environment, the two values hval and tval are provided. these values are stored in volatile registers. hval the number hval represents the digital output value y which is proportional to the applied magnetic field. hval is 16-bit two?s complement binary ranging from ? 32768 to + 32767. note: the number of valid bits varies between 13 and 16 bit. the resolution depends on the selected sample and filter frequency. it is stored in the hvd register (see section 5.2. on page 27). in case of internal overflows, the output will clamp to the maximum or minimum hval value. please take care that during calibration, the output sig- nal range does not reach the maximum/minimum value. tval the number tval provides the adjusted value of the built-in temperature sensor. tval is a 16-bit two?s complement binary ranging from ? 32768 to 32767. it is stored in the tvd register (see section 5.2. on page 27). note: the actual resolution of the temperature sensor is 12 bit. the 16-bit representation avoids rounding errors in the computation. the relation between tval and the junction tempera- ture t j is c tval () c 0 c 1 tval c 2 tval 2 ? + ? += d tval () d 0 d 1 tval ? += y hval 32768 --------------- - = t j 0 tval + 1 ? = free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 9 2.2.2. dsp configuration registers this section describes the function of the dsp configu- ration registers. for details on the eeprom please refer to section 5.5. on page 29. magnetic range: range the range register defines the magnetic range of the a/d converter. the range register has to be set according to the applied magnetic field range. it can be varied between: typical 20 mt and 160 mt in steps of 20 mt. for details, see section 5.5. on page 29. note: the a/d values are not temperature compen- sated. please take care that the a/d is not satu- rating over the used temperature range. filter settings: fs and resolution of hvd the fs register defines the sampling frequency of the built in digital low-pass filter. hal 2831/hal 2833 transmit 16 data bits for sampling frequencies below 500 hz. side effect is that the sent protocol is extended by a fourth data nibble. fig. 2?3 shows the sensor?s transfer function. the transfer functions for all recommended settings of fs have been combined in this graph. the upper graph of fig. 2?3 shows the magnitude at the pass band and stop band. the lower graph is a zoom-in of the magnitude at the pass band. the sensors have a linear phase behavior for sample frequencies of 1 or 2 khz and a constant group delay. for the remaining sample frequencies, the phase is nearly linear at the pass band and the group delay is nearly constant. all filter combinations have a very constant gain at the pass band and a high attenuation at the stop band. the low pass filter is of first order for 1 or 2 khz filter frequency. at the remaining sample frequencies, the low pass filter is of second order. thus, the slope at the cut-off frequency is bigger. the graphs do include the transfer function of the hall adc (adc and decimation filter) and the digital filter. table 2?1: relation between t j and t adj (typical values) coefficient value unit 0 71.65 c 1 1 / 231.56 c free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 10 sept. 6, 2010; ai000143-002en micronas fig. 2?3: transfer function, magnitude 10 0 10 1 10 2 10 3 -5 -4.5 -4 -3.5 -3 -2.5 -2 -1.5 -1 -0.5 0 |h(f)| [db] f [hz] transfer function f s = 1953 hz f s = 976.6 hz f s = 488.3 hz f s = 244.1 hz f s = 122.1 hz f s = 61.04 hz f s = 30.52 hz 10 0 10 1 10 2 10 3 -25 -20 -15 -10 -5 0 5 |h(f)| [db] f [hz] transfer function f s = 1953 hz f s = 976.6 hz f s = 488.3 hz f s = 244.1 hz f s = 122.1 hz f s = 61.04 hz f s = 30.52 hz free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 11 table 2?2: available sample frequencies and low pass filter. magnetic offset d the d (offset) registers contain the parameter for the adder in the dsp. the added value is a first order poly- nomial of the temperature. d0 register d0 is encoded as two?s complement binary. d1 register d1 is encoded as two?s complement binary. sample frequency fs resolution of hvd recommend clock tick time sensor type no pause pulse pause pulse typ. hal 2831/3 hal 2830/2 hal 2831 hal 2830 hal 2833 hal 2832 [hz] [ms] [hex] [lsb] [lsb] [s] 2000 0.5 0x00 13 13 2) 2.25 2.00 and 2.50 2.00 2.00, 2.25 1000 1 0x01 15 15 2) 2.00 to 4.50 2.00 to 5.25 2.00 to 4.25 2.00 to 5.00 500 2 0x03 16 16 2) 2.00 to 9.25 2.00 to 10.75 2.50 1) to 8.75 2.50 1) to 10.00 250 4 0x07 2.00 to 17.75 2.00 to 17.75 4.75 1) to 17.75 4.75 1) to 17.75 125 8 0x0b 9.25 1) to 17.75 9.5 1) to 17.75 62 16 0x0f n.a. 1) n.a. 1) 31 32 0x13 1) limited by the maximum pause pulse length specified in sae-j2716. 2) a resolution of 12-bit is guaranteed only. table 2?3: temperature independent coefficient parameter range resolution d 0 ? 0.5508 ... 0.5497 10 bit d0 ? 512 ... 511 d 0 0,5508 512 ---------------- d 0 ? = table 2?4: linear temperature coefficient parameter range resolution d 1 ? 3.076 x 10 ? 6 ... 3.028 x 10 ? 6 7bit d1 ? 64 ... 63 d 1 0,1008 64 ---------------- d 13,051810 5? ?? ? = free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 12 sept. 6, 2010; ai000143-002en micronas magnetic sensitivity c the c (sensitivity) registers contain the parameter for the multiplier in the dsp. the multiplication factor is a second order polynomial of the temperature. c0 register c0 is encoded as two?s complement binary: c1 register c1 is encoded as two?s complement binary. c2 register c2 is encoded as two?s complement binary. 2.3. power-on self test (post) the hal 283x features a built-in power-on self test to support in system start-up tests to enhanced the sys- tem failure detection possibilities. the power-on self test comprises the following sensor blocks: ?ram ?rom ?eeprom ? full signal path included (hall-plates, adc, low pass filter, temperature compensation and the sent output) the power-on self test can be activated by setting cer- tain bits in the sensor?s eeprom. also the test com- plexity is customer selectable. the following table shows the available test combinations. table 2?8: power-on self test modes note: please contact micronas for further information about power-on self test. table 2?5: temperature independent coefficient parameter range resolution c 0 ? 2.0810 ... 2.2696 12 bit c0 ? 2048 ... 2047 table 2?6: linear temperature coefficient parameter range resolution c 1 ? 7.955 x 10 ? 6 ... 1.951 x 10 ? 5 9bit c1 ? 256 ... 255 table 2?7: quadratic temperature coefficient parameter range resolution c 2 ? 1.87 x 10 ? 10 ... 1.86 x 10 ? 10 8bit c2 ? 128 ... 127 c 0 2,1758 2048 ---------------- c 0 89,261 + () ? = c 1 0,4509 256 --------------- - c 1 108,0 + () 3,0518 10 5? ??? = c 2 0,2008 128 --------------- - c 29,313210 10? ?? ? = eeprom.post mode / function [2] [1] [0] x x 0 post disabled. x 0 1 memory test only enabled (ram, rom, eeprom). x 1 1 memory test and signal path stimu- lation enabled. 0 x 1 post errors will be reported at the register pte only. hall values will be transmitted after post fails. 1 x 1 post errors will be reported at the status register pte and do force hval to ? 32768. no hall values will be transmitted after post fails. free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 13 3. specifications 3.1. outline dimensions fig. 3?1: to92ut-2 plastic transistor standard ut package, 3 leads weight approximately 0.105 g free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 14 sept. 6, 2010; ai000143-002en micronas fig. 3?1: to92ut-1 plastic transistor standard ut package, 3 leads, spread weight approximately 0.105 g free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 15 fig. 3?1: to92ut-1 : dimensions ammopack inline, spread free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 16 sept. 6, 2010; ai000143-002en micronas fig. 3?2: to92ut-2 : dimensions ammopack inline, not spread free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 17 3.2. dimensions of sensitive area 0.213 mm x 0.213 mm 3.3. positions of sensitive area 3.4. absolute maximum ratings stresses beyond those listed in the ?absolute maximum ratings? may cause permanent damage to the device. this is a stress rating only. functional operation of the device at these conditions is not implied. exposure to absolute maximum rating conditions for extended periods will affect device reliability. this device contains circuitry to protect the inputs and outputs against damage due to high static voltages or electric fields; however, it is advised that normal precautions be taken to avoid application of any voltage higher than abso- lute maximum-rated voltages to this high-impedance circuit. all voltages listed are referenced to ground (gnd). 3.4.1. storage, moisture sensitivity class, and shelf life the permissible storage time (shelf life) of the sensors is unlimited, provided the sensors are stored at a maximum of 30 c and a maximum of 85% relative humidity. at these conditions, no dry pack is required. solderability is guaranteed for one year from the date code on the package. to92ut-1/2 a4 0.4 mm bd 0.3 mm d1 min. 4.0 mm, max. 4.1 mm y 1.5 mm nominal h1 min. 22.0 mm, max. 24.1 mm symbol parameter pin name min. max. unit condition t j junction operating temperature ?? 40 190 1) c not additive v sup supply voltage vsup ? 18 26.5 40 v v t < 5 min. t < five times 400 ms not additive v dio io voltage dio ? 0.3 26.5 v t < 5 min. b max magnetic field ?? unlimited t v esd esd protection 2) vsup, dio ? 8.0 8.0 kv 1) for 96 h - please contact micronas for other temperature requirements. 2) jesd22-a-114 (100 pf and 1.5 k ) free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 18 sept. 6, 2010; ai000143-002en micronas 3.5. recommended operating conditions functional operation of the device beyond those indicated in the ?recommended operating conditions/characteris- tics? is not implied and may result in unpredictable behavior, reduce reliability and lifetime of the device. all voltages listed are referenced to ground (gnd). 3.6. electrical characteristics at t j = ? 40 c to +170 c, v sup = 4.5 v to 18 v, after programming the sensor and locking the dsp config eeprom, at recommended operating conditions if not otherwise specified in the column ?conditions?. typical characteristics for t a = 25 c and v sup = 5 v. for all other temperature ranges this table is also valid, but only in the junction temperature range defined by the tem- perature grade (example: for k-type this table is limited to t j = ? 40 c to +140 c). symbol parameter pin name min. max. unit remarks v sup supply voltage vsup 4.5 18 v v dio output voltage dio 0 18 v i dio continuous output current dio ? 20 ma for v dio = 0.8 v v pull-up pull-up voltage ? 3.0 18 v in typical applications v pull-up,max = 5.5 v r pull-up pull-up resistor dio (see section 6.3. on page 29) c l load capacitance dio 180 (see section 6.3. on page 29) pf n prg number of eeprom programming cycles ?? 100 cycles 0 c hal 283x advance information 20 sept. 6, 2010; ai000143-002en micronas 3.8. thermal characteristics at recommended operating conditions if not otherwise specified in the column ?conditions?, t j = ? 40 c to +170 c, v sup = 4.5 v to 18 v. 3.8.1. definition of sensitivity error es es is the maximum of the absolute value of 1 minus the quotient of the normalized measured value 1) over the normalized ideal linear 2) value: in the example shown in fig. 3?3 on page 21, the maximum error occurs at ? 10 c: symbol parameter pin name min. typ. max. unit conditions to92ut package r thja r thjc r thjs thermal resistance junction to ambient junction to case junction to solder point ? ? ? ? ? ? ? 235 61 128 k/w k/w k/w measured on 1s0p board measured on 1s0p board measured on 1s0p board 1) normalized to achieve a least-square-fit straight-line that has a value of 1 at 25 c 2) normalized to achieve a value of 1 at 25 c es max abs meas ideal ----------- - 1? ?? ?? ?? ?? tmin, tmax [] = es 1,001 0,993 ------------ - 1 ?0.8% == free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 21 fig. 3?3: definition of sensitivity error (es) 50 75 100 125 150 175 25 0 ?25 ?50 0.98 0.99 1.00 1.01 1.02 1.03 -10 0.993 1.001 temperature [c] relative sensitivity related to 25 c value ideal 200 ppm/k least-square-fit straight-line of normalized measured data measurement example of real sensor, normalized to achieve a value of 1 of its least-square-fit straight-line at 25 c free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 22 sept. 6, 2010; ai000143-002en micronas 4. the sent module the sent interface is used for transmitting hall values from the sensor to an ecu. additional information is transmitted by serial data messages in the status nib- ble. HAL2830/hal 2831 feature a sent output with- out pause pulse and hal 2832/hal 2833 provides sent messages with pause pulse. all sensors of the family hal 283x supports the related sae standards. fig. 4?1, fig. 4?2, fig. 4?3 and table 4?1 describe the sent timing in detail. a sent message consists of a synchronization / cali- bration pulse, a status and communication nibble, three or four data nibbles, a crc nibble, and an optional pause pulse (only for hal 2832/hal 2833). fig. 4?1, fig. 4?2, and fig. 4?3 are valid for sent messages with three data nibbles. the timing of a sent message with four data nibbles is similar. the fourth data nibble is inserted between the third data nibble and the crc nibble. it has the same character- istics as the remaining data nibbles. see table 4?4 for the description of the pulses/nibbles of a message. the number of data nibbles depends on the sensor type. after reset, the output is high. the transmission of sent messages starts immediately after initialization. due to the fact that the first valid hall value will be typ- ically calculated after the transmission has been started, the sensor transmits the initial value of hvd.hval first. in case of an overcurrent at the dio output, the output transistor will be switched off (high impedance). fig. 4?1: sent interface startup timing of hal 283x fig. 4?2: sent interface timing in case of HAL2830/hal 2831 vsup dio t sync t startup t nlow calibration / synchronization status d[11:8] t nibble t nibble t sync t nlow calibration / synchronization status d[11:8] t nibble t nibble crc (previous telegram) t nlow d[7:4] t nibble d[3:0] t nibble crc t nibble t message free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 23 fig. 4?3: sent interface timing in case of hal 2832/hal 2833 table 4?1: sent interface timing symbol parameter min. typ. max. unit condition / remark t tick clock tick time 2.00 1)2) ? 17.75 1)2) s t nlow nibble low time 5) 3) s 3.00 6.75 t tick due to truncation errors, the max. low time may be slightly smaller at some clock tick times. v/ t fall falling edge slew rate (see section 3.6. on page 18) not reverse voltage protected i/o logic, typical slew rate = 1 v/s v/ t rise rising edge slew rate (see section 3.6. on page 18) not reverse voltage protected i/o logic, typical slew rate = 2 v/s t sync calibration / synchronization pulse period 56 t tick t nibble nibble pulse period 12 27 t tick t nibble = 12 + data t pause pause pulse period 12 4) 768 4) t tick only available for hal 2832/ hal 2833 t message message time (see table on page 26) t delay_sm new hall sample to mes- sage start delay 1t message sent message without pause pulse (HAL2830/ hal 2831) tbd s sent message with pause pulse (hal 2832/ hal 2833) 1) clock tolerance of +/- 10 % is not included 2) t tick = (8 + tick) 0.25 s, tick = 0 to 63 [0.227 s to 0.278 s] 3) t nlow = trunc( (8 + tick) (12 + lt) / 4) 0.25, tick = 0 to 63, lt = 0 to 15 [0.227 s to 0.278 s] 4) specified value of sae-j2716 2010-01. it is necessary to select an appropriate sample rate and clock tick time to guarantee the limit. 5) internal timing only. the timing at the output pin depends on the selected tick time due to the different recommended slew rates. internal low time and external low time are nearly identical for tick times t tick = 2 s to 2.5 s. tick times t tick > 2.5 s generate an offset between internal and external nibble low time. the offset can be calculated as follows: offset ~ (v pull-up - v ol )/ v/ t rise - (v pull-up -v ol )/ v/ t fall t sync t nlow calibration / synchronization status d[11:8] t nibble t nibble pause (previous telegram) t nlow d[7:4] t nibble d[3:0] t nibble crc t nibble t message pause t pause free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 24 sept. 6, 2010; ai000143-002en micronas in case of HAL2830/hal 2831 the message time of a sent message depends on the configured tick time and the transmitted data value. the sent messages are transmitted asynchronously to the hall samples. see table 4?2 for recommended tick times. in case that slower tick times will be chosen, hall samples may be lost and aliasing may occur. when using the recom- mended tick times, samples may be transmitted twice in series due to the fact that the mean message time is shorter than the hall sample time. a rdbl (read dou- ble) flag has been implemented for marking messages which does not contain a new hall sample. the rdbl flag is located in the register sps and is transmitted by the status and communication nibble. this is not necessary for hal 2832/hal 2833 with pause pulse. for these devices the sent messages are synchronous with the delivery of new hall sam- ples. one sent message is transmitted per hall sam- ple. thus, the propagation delay is very low and the message time is nearly constant. see table 4?2 for recommended tick times. the usage of tick times slower than recommended may lead to corrupted sent messages. the usage of tick times faster than recommended may lead to a pause pulse which exceeds the limit specified in sae-j2716 2010-01. additional information is transmitted by serial data messages (short format). serial messages are trans- mitted by bit 2 and 3 of the status nibble. see sae- j2716 for more information about the short serial data message format. see table 4?5 for the used ids and the data content of the ids. the ids are continuously transmitted from the lowest id to highest id. the sent clock tick time can be configured by the eeprom bit field tick. see table 4?1 and table 4?2. the low time can be configured by the eeprom bit field lt. see table 4?1 and table 4?2. the adjusted slew rate depends on the sent clock tick time. see table 4?1. table 4?2: recommended settings for low tick time tick t tick slew rate min. recommended low time max. recommended low time remark typ. typ. lt t nlow lt t nlow [lsb] [ s] [v/ s] [lsb] [t tick ] [ s] 1) [lsb] [t tick ] [ s] 1) 0 2.00 2 0 3.00 6.00 15 6.75 13.50 1 2.25 6.75 6.67 15.00 2 2.50 7.50 6.70 16.75 3 2.75 1 2 3.45 9.50 11 5.73 15.75 4 3.00 1 3.25 9.75 13 6.25 18.75 5 3.25 0 3.00 9.75 14 6.46 21.00 6 3.50 10.50 15 6.71 23.50 8 4.00 12.00 6.75 27.00 12 5.00 15.00 6.75 33.75 63 17.75 53.25 6.75 119.75 1) clock tolerance of 10 % is not included free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 25 table 4?3: recommended settings for sae-j2716 compliance tick t tick slew rate min. recommended low time max. recommended low time remark typ. typ. lt t nlow lt t nlow [lsb] [ s] [v/ s] [lsb] [t tick ] [ s] 1) [lsb] [t tick ] [ s] 1) 3 2.75 1 4 4.00 11.00 11 5.73 15.75 4 3.00 12.00 13 6.25 18.75 5 3.25 13.00 14 6.46 21.00 6 3.50 14.00 15 6.71 23.50 8 4.00 16.00 6.75 27.00 12 5.00 20.00 6.75 33.75 63 17.75 71.00 6.75 119.75 1) clock tolerance of 10 % is not included table 4?4: nibble / pulse description # pulse number of clock ticks description min. max. 1 synchronization/ calibration 56 it is recommended to measure the synchronization / calibration period for calibration of the clock tick time t tick at the ecu. 2status & communication nibble 12 27 bit 0: sps.rdbl (hall sample has been already transmitted) bit 1: mds.pto (power on test is operating) bit 2: serial message data bit (see sae-j2716) bit 3: serial message start (see sae-j2716) 3 data nibble 1 hvd[15:12] 4 data nibble 2 hvd[11:8] 5 data nibble 3 hvd[7:4] - / 6 data nibble 4 (optional) hvd[3:0] only in case of hal 2831/hal 2833 6 / 7 crc nibble checksum of data nibble 1 to data nibble 4. see sae-j2716 2008-02 or sae-j2716 2010-01 for more information. - / 7 / 8 pause pulse (optional) 12 1) 768 1) only for hal 2832/hal 2833 1) recommended value. see table 4?1 for more information free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 26 sept. 6, 2010; ai000143-002en micronas table 4?5: serial message content id content remark 0 sn[7:0] serial number, byte 1 1 sn[15:8] serial number, byte 2 2 sn[23:16] serial number, byte 3 3 sn[31:24] serial number, byte 4 4 tvd[7:0] temperature value data register. high byte must be captured when low byte is read for transmission. 5tvd[15:8] 6 spe signal path status register 7 ds device status register 8 pte power-on test error register 9 sysclk[7:0] system clock, byte 1 10 sysclk[15:8] system clock, byte 2 table 4?6: message length tick t tick sent message sensor type HAL2830/2 hal 2831/3 message length in t tick and s (brackets) 3) [lsb] [ s] min. max. min. max. 02.00116 (232 s) 191 (382 s) 128 (256 s) 218 (436 s) 12.25116 (261 s) 191 (430 s) 128 (288 s) 218 (491 s) 22.50116 (290 s) 191 (478 s) 128 (320 s) 218 (545 s) 32.75116 (319 s) 191 (525 s) 128 (352 s) 218 (560 s) 43.00116 (348 s) 191 (573 s) 128 (384 s) 218 (654 s) 84.00116 (464 s) 191 (764 s) 128 (512 s) 218 (872 s) 12 5.00 116 (580 s) 191 (955 s) 128 (640 s) 218 (1090 s) 63 17.75 116 (2059 s) 191 (3390 s) 128 (2272 s) 218 (3870 s) 1) recommended min. message time. t message = max. t message of no pause pulse + 12 ticks 2) recommended max. message time. t message = min. t message of no pause pulse + 256 * 3 ticks 3) clock tolerance of 10 % is not included free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 27 5. programming of the sensor hal 283x features two different customer modes. in application mode the sensor provides a continuos pwm signal transmitting temperature-compensated magnetic field values. in programming mode it is possible to change the register settings of the sensor. after power-up the sensor is always operating in the application mode . it is switched to the programming mode by a defined sequence on the sensor output pin. 5.1. programming interface in programming mode the sensor is addressed by modulating a serial telegram (biphase-m) with con- stant bit time on the output pin. the sensor answers with a modulation of the output voltage. a logical ?0? of the serial telegram is coded as no level change within the bit time. a logical ?1? is coded as a level change of typically 50% of the bit time. after each bit, a level change occurs (see table 5?1). the serial telegram is used to transmit the eeprom content, error codes and digital values of the magnetic field or temperature from and to the sensor. fig. 5?1: definition of logical 0 and 1 bit a description of the communication protocol and the programming of the sensor is available in a separate document (application note programming hal 283x). logical 0 or t bbit t bbit logical 1 or t bbit t bbit t bhb t bhb t bhb t bhb table 5?1: biphase-m frame characteristics of the host symbol parameter min. typ. max. unit remark t bbit (host) biphase bit time 970 1024 1075 s t bhb (host) biphase half bit time 0.45 0.5 0.55 t bbit (host) t bifsp (host) biphase interframe space 3 ?? t bbit (host) v outl voltage for low level tbd tbd tbd v v outh voltage for high level tbd tbd tbd v v ddprg supply voltage during programming 5.5 ? 18 v table 5?2: biphase-m frame characteristics of the sensor symbol parameter min. typ. max. unit remark t bbit (sensor) biphase bit time 820 1024 1225 s t bhb (sensor) biphase half bit time ? 0.5 ? t bbit (sensor) t bresp biphase response time 1 ? 5t bbit (sensor) slew rate 2 v/s free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 28 sept. 6, 2010; ai000143-002en micronas 5.2. programming environment and tools for the programming of hal 283x during product development and also for production purposes a pro- gramming tool including hardware and software is available on request. it is recommended to use the micronas tool kit in order to ease the product develop- ment. the details of programming sequences are also available on request. 5.3. programming information for production and qualification tests, it is mandatory to set the lock bit after final adjustment and program- ming of hal 283x. the lock function is active after the next power-up of the sensor. the success of the lock procedure should be checked by reading the status of the lock bit after locking and/or by a check of the sensors output signal. electrostatic discharge (esd) may disturb the pro- gramming pulses. please take precautions against esd and check the sensors error flags. free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 29 6. application notes 6.1. ambient temperature due to the internal power dissipation, the temperature on the silicon chip (junction temperature t j ) is higher than the temperature outside the package (ambient temperature t a ). at static conditions and continuous operation, the fol- lowing equation applies: for typical values, use the typical parameters. for worst case calculation, use the max. parameters for i sup and r th , and the max. value for v sup from the application. the choice of the relevant r thjx -parame- ter (r thja , r thjc , or r thjs ) depends on the way the device is (thermally) coupled to its application environ- ment. for the hal 283x, the junction temperature t j is spec- ified. the maximum ambient temperature t amax can be calculated as: 6.2. emc and esd for applications that cause disturbances on the supply line or radiated disturbances, a series resistor and a capacitor are recommended. the series resistor and the capacitor should be placed as closely as possible to the hall sensor. please contact micronas for detailed investigation reports with emc and esd results. 6.3. application circuit micronas recommends the following two application circuits for the hal 283x. the external circuit mentioned in fig. 6?1 is recom- mended when v bat v pull-up . it is typically used when the supply pin is directly connected with the battery voltage and the dio pin operates on a regulated power supply. fig. 6?2 shows the recommended circuit according to the sae-j2716 2010-01. it can be used when v bat = v pull-up < 7 v. the pull-up resistor r pull-up1 must be placed close to the sensor to be compliant with the sent specification. for saving external components, the resistors r pull-up1 and r pull-up2 could be combined to r pull-up and placed close to the ecu. this might be possible for some applications only and will not be compliant with the sent specification. the electrical characteristics mentioned in section 3. (e.g. v sup ) has to be considered at the system setup. they may reduce the operation range. values of external components: c vsup = 47 nf c dio = 180 pf the maximum allowed load capacitor and the mini- mum resistance can be calculated with the following equation: c l = c dio + c wire + c input r l = r pull-up r l ( v pull-up (max.) ? v diol (max.) ) / ( i dio ? ( c l ( v/ t fall ) c l 0.4 v pull-up (min.) / ( r l ( v/ t rise ) ) r pull-up = r pull-up1 || r pull-up2 r pull-up : pull-up resistor between dio and v pull-up c vsup : capacitance between the vsup pin and gnd c dio : emc protection capacitance on the dio pin c wire : capacity of the wire c input : input capacitance of the ecu v pull-up (max.) : max. applied pull-up voltage, must be lower than the value specified in section 3.5. v pull-up (min.) : min. applied pull-up voltage, must be higher than the value specified in section 3.5. v diol (max.) : max. dio low voltage, it is recommended to use the value specified in section 3.6. i dio : dio current at v diol (max.) v/ t rise : selected rising edge slew rate, the max. value specified in section 3.6. has to be used v/ t fall : selected falling edge slew rate, the max. value specified in section 3.6. has to be used t j t a t += t i sup v sup r thjx i dio v dio r thjx + = t amax t jmax t ?= free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 30 sept. 6, 2010; ai000143-002en micronas example for calculating r l and c l (max.) the application operates at following conditions: falling slew rate = 1 v/s (typ.) rising slew rate = 0.5 v/s (typ.) v pull-up = 5.5 v (max.) c l = 400 pf calculation: r l (5.5 v ? 0.8 v) / (20 ma ? 400 pf 1.3 v/s) = 241 ohm r l = 1000 ohm check c l : c l = 400 pf 0.4 4.5 v / (1000 ohm 0.65 v/s) = 2.77 nf the used c l is below the limit. fig. 6?1: recommended external circuit for v bat v pull-up fig. 6?2: recommended external circuit for v bat = v pull-up < 7v note: the external components needed to protect against emc and esd may differ from the application circuit shown and have to be determined according to the needs of the application specific environment. dio gnd vsup c vsup c dio input gnd c input hal 283x ecu c wire r pull-up v bat = 12 v (typ.) v pull-up = 5 v (typ.) dio gnd vsup c vsup c dio input gnd c input hal283x ecu c wire r pull-up2 v sup = v pull-up (typ. 5v) r pull-up1 > 10k r pull-up2 and c input are the equivalent circuit of the ecu. free datasheet http://www.datasheet-pdf.com/ advance information hal 283x micronas sept. 6, 2010; ai000143-002en 31 free datasheet http://www.datasheet-pdf.com/ hal 283x advance information 32 sept. 6, 2010; ai000143-002en micronas micronas gmbh hans-bunte-strasse 19 ? d-79108 freiburg ? p.o. box 840 ? d-79008 freiburg, germany tel. +49-761-517-0 ? fax +49-761-517-2174 ? e-mail: docservice@micronas.com ? internet: www.micronas.com 7. data sheet history 1. advance information: ?hal 283 0 linear hall-effect sen s or family with sent interface?, oct. 9, 2008, ai000143-001en. first release of the advance infor- mation. originally created for hw version hapb-2-f & 2-g. 2. advance information: ?hal 283x linear hall-effect sensor family with sent interface?, sept. 6, 2010, ai000143-002en. second release of the advance information. free datasheet http://www.datasheet-pdf.com/ |
Price & Availability of HAL2830
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |